News

In the field of industrial production, industrial chillers, as key cooling equipment, play a crucial role in ensuring the continuity of production and product quality. And the quality of industrial chiller parts is the core factor that determines its overall performance and reliability.   First of all, high-quality parts are the foundation for ensuring the efficient operation of industrial chillers. For example, the compressor, as the core component of the chiller, directly affects the refrigeration efficiency and stability. High-quality compressors can maintain stable performance during long-term operation and provide reliable refrigeration effects, thereby reducing energy consumption and improving production efficiency. The quality of condensers and evaporators is equally important. They are responsible for heat exchange. Efficient condensers and evaporators can quickly and effectively dissipate heat and ensure that the refrigeration capacity of the chiller is always in the best state.   Secondly, good part quality helps extend the service life of industrial chillers. In an industrial environment, chillers usually need to operate continuously for a long time and endure various harsh working conditions. If the part quality is not up to standard, problems such as wear, corrosion, and damage are prone to occur, thereby shortening the service life of the chiller. High-quality parts have better durability and corrosion resistance and can operate stably for a long time in harsh environments, reducing equipment maintenance and replacement costs.   Furthermore, high-quality parts can improve the safety of industrial chillers. For example, the quality of parts in the electrical control system is directly related to the safe operation of the equipment. High-quality electrical components can ensure the stability and reliability of the circuit and avoid safety accidents caused by electrical failures. At the same time, high-quality pressure sensors, temperature sensors and other parts can accurately monitor the operating status of the chiller and detect and handle potential safety hazards in time.   In addition, high-quality parts can also improve the maintenance convenience of industrial chillers. When it is necessary to maintain and service the chiller, parts of good quality are easier to disassemble and install, reducing maintenance time and difficulty. Moreover, high-quality parts have a lower failure rate, reducing the frequency and cost of maintenance.   In conclusion, the importance of industrial chiller parts quality cannot be ignored. High-quality parts can not only ensure the efficient operation of chillers, extend service life, improve safety, but also improve maintenance convenience and provide reliable cooling guarantees for industrial production. Therefore, when choosing and using industrial chillers, great attention should be paid to part quality and choose high-quality products and reliable suppliers to ensure the sm...

As a new type of mixed refrigerant, R410 refrigerant is emerging in the market with its efficient refrigeration performance and relatively environmentally friendly characteristics. It is composed of R32 and R125 in a certain proportion and has stable chemical properties and excellent heat transfer efficiency.   In terms of environmental protection, the ozone depletion potential (ODP) of R410 refrigerant is zero, greatly reducing the harm to the earth's ozone layer. At the same time, its relatively low global warming potential (GWP) also makes it have positive significance in addressing climate change. With the increasing global attention to environmental protection, this advantage of R410 makes it the preferred choice for many refrigeration equipment manufacturers and users.   From a performance perspective, refrigerant R410 can achieve efficient refrigeration in a wider temperature range. Whether in hot summers or cold winters, it can maintain a stable refrigeration effect and provide a comfortable environment for industrial production and daily life. In addition, R410 also has a relatively high pressure ratio and can adapt to various types of refrigeration equipment to improve the operating efficiency of the equipment.   Many enterprises are also increasing their investment in the research and application of R410 refrigerant. Some industrial refrigeration equipment manufacturers have begun to launch new products using R410 refrigerant to meet the market's demand for efficient and environmentally friendly refrigeration solutions. At the same time, relevant technical experts are constantly exploring how to further optimize the performance of R410, reduce its use cost, and improve its applicability in different fields.   However, although refrigerant R410 has many advantages, it also faces some challenges in the process of promotion and application. For example, due to its relatively high pressure, the sealing and pressure resistance requirements for refrigeration equipment are also correspondingly increased, which may increase the manufacturing cost of the equipment. In addition, the recycling and treatment of R410 also require professional technology and equipment to ensure that it will not cause secondary pollution to the environment.   In general, as an efficient and environmentally friendly refrigeration choice, refrigerant R410 has broad development prospects. With the continuous progress of technology and the continuous improvement of environmental awareness, it is believed that R410 will play an increasingly important role in the field of industrial refrigeration and contribute to promoting sustainable development.

In the field of industrial production, industrial refrigeration chillers play a crucial role as they can effectively provide a stable low-temperature environment for various equipment and processes. However, in daily use, the chiller may experience various faults and issue alarms. This not only affects production progress but may also cause damage to the equipment. Therefore, understanding how to release the alarms of industrial refrigeration chillers and the handling methods for common faults is of utmost importance.   I. The Importance of Chiller Alarms   The alarm system of chillers is designed to promptly remind users of abnormal conditions in the equipment so that corresponding measures can be taken for handling. These alarm messages usually include excessive temperature, abnormal pressure, water flow faults, and more. If not addressed in time, it may lead to equipment damage, production interruption, and even safety accidents.   II. Alarm Release Guide   Understand the meaning of alarm codes Different chiller brands and models may have different alarm codes. Users should first consult the equipment manual to understand the specific meanings of various alarm codes. This will help quickly determine the cause of the fault and take appropriate solutions. Check the equipment operating status When the chiller issues an alarm, immediately check the operating status of the equipment. This includes checking whether parameters such as water temperature, pressure, and water flow are normal. At the same time, observe whether there are abnormal noises, vibrations, or leaks in the equipment. Eliminate the cause of the fault Based on the alarm code and equipment operating status, gradually eliminate the cause of the fault. For example, if there is an excessive temperature alarm, it may be caused by a clogged condenser, insufficient refrigerant, or a malfunctioning cooling fan. Take corresponding solutions for different fault causes. Reset the alarm system After eliminating the fault, the alarm system needs to be reset. Usually, this can be achieved by pressing the reset button on the equipment or operating in the control system. After resetting, observe whether the equipment is operating normally to ensure that the alarm has been released.   III. Handling Methods for Common Faults   Excessive temperature fault Causes: Clogged condenser, insufficient refrigerant, malfunctioning cooling fan, etc. Handling methods: Clean the condenser, add refrigerant, and check whether the cooling fan is working properly. If the cooling fan is malfunctioning, it should be replaced or repaired in time. Abnormal pressure fault Causes: Refrigerant leakage, clogged filter, malfunctioning expansion valve, etc. Handling methods: Check whether there is a leakage in the refrigerant pipeline, replace the clogged filter, and adjust or replace the expansion valve. If the pressure is too high, some refrigerant can be released to reduce the pressure. Water ...

With the continuous development of industrial production, the requirements for refrigeration equipment are also increasing day by day. Dongguan Zili Refrigeration Electromechanical Equipment Co., Ltd. always adheres to the innovation-driven development strategy, actively invests in R & D resources, and is committed to providing customers with more efficient and intelligent refrigeration solutions. The launch of this cold and hot integrated chiller is the concentrated expression of the company's innovation achievements.   This cold and hot integrated chiller has many excellent performance advantages. First of all, it integrates refrigeration and heating functions, and can quickly switch working modes according to different production needs, greatly improving the adaptability and flexibility of the equipment. Whether it is needed for cooling in hot summer or providing heat source in cold winter, this chiller can easily handle it.   Secondly, the cold and hot integrated chiller adopts an advanced intelligent control system, which can realize precise temperature control and automated operation. Users can easily set the required temperature parameters through a simple operation interface, and the equipment will automatically adjust the operating state to ensure that the temperature is always within the set range. At the same time, the intelligent control system also has a fault self-diagnosis function, which can detect and eliminate equipment failures in time and improve the reliability and stability of the equipment.   In addition, during the research and development process, Dongguan Zili Refrigeration Electromechanical Equipment Co., Ltd. fully considered the requirements of energy conservation and environmental protection. The cold and hot integrated chiller adopts an efficient compressor and heat exchanger, which can significantly reduce energy consumption and reduce the impact on the environment. At the same time, the operating noise of the equipment has also been effectively controlled, providing users with a more quiet and comfortable working environment.   The launch of the cold and hot integrated chiller has received high attention and recognition from many customers. Many enterprises have expressed that this new type of chiller will bring great convenience and benefits to their production. The person in charge of Dongguan Zili Refrigeration Electromechanical Equipment Co., Ltd. said that the company will continue to increase R & D investment and continuously launch more innovative products to make greater contributions to the development of the refrigeration industry.   It is believed that with the efforts of Dongguan Zili Refrigeration Electromechanical Equipment Co., Ltd., the cold and hot integrated chiller will surely shine brightly in the market and lead the refrigeration industry to a new height.

The role of plastic recycling crushers is extremely important. It can efficiently crush various waste plastic products, such as beverage bottles, plastic bags, plastic containers, etc. Through powerful crushing force, these originally difficult-to-handle waste plastics are broken into uniform small particles. The reverse claw design brings higher crushing efficiency to plastic crushers. When traditional plastic crushers handle some plastic products with high hardness or irregular shapes, problems such as incomplete crushing and jamming may occur. However, the reverse claw design, through a special structure, can better grab and crush plastic materials during the crushing process, making the crushing more uniform and thorough.   This design also improves the stability and reliability of the equipment. The presence of reverse claws can effectively reduce vibration and noise during the crushing process, reduce the degree of equipment wear, and extend the service life of the equipment. At the same time, the reverse claw design can also prevent plastic materials from splashing during the crushing process, improving operational safety.   In addition, plastic crushers with reverse claw design also have the characteristics of energy conservation and environmental protection. Due to its efficient crushing ability, it can reduce energy consumption. At the same time, the crushed plastic particles are more uniform, which is conducive to subsequent processing and reuse, reducing waste of resources.   In conclusion, plastic crushers with reverse claw design have become important equipment in the plastic recycling and treatment industry with their unique advantages. It not only improves crushing efficiency and the stability of the equipment but also contributes to energy conservation and environmental protection. In the future, as the demand for plastic recycling and reuse continues to increase, plastic crushers with reverse claw design will surely play an even more important role.